|
AXA VERTICALA
|
|
senzitivitate
|
5mV~5V/DIV, 10 steps in 1-2-5 sequence (X5 MAG: 1mV/DIV)
|
|
Acuratetea senzitivitatii
|
≤3% (×5MAG: ≤5%)
|
|
Vernier vertical sensitivity
|
continuously variable to 1/2.5 or less of panel-indicated value
|
|
Banda de frecventa
|
DC-20MHz (×5MAG:DC-7MHz)
DC-40MHz (×5MAG:DC-15MHz)
|
|
AC coupling
|
Low limit frequency 10Hz. (With reference to 100KHz,8DIV.Frequency response with-3dB)
|
|
Rise time
|
Approx.17.5Ns (×5MAG:Approx.50Ns) / 9.5nS (X5MAG: Approx.25nS)
|
|
Input impedance
|
Approx. 1M ohm//Approx. 25pF
|
|
Square wave characteristics
|
Overshoot: ≤5%(At 10Mv/DIV range) other distortions and other ranges: 5% added to the above value
DC balance shift: 5mV~5V/DIV; ±0.5 DIV, 1mV~2mV/DIV±2.0DIV
Linearity: ﹤ ±0.1DIV of amplitude change when waveform of 2 DIV at graticule center is moved vertically.
|
|
Vertical modes
|
CH1 single channel.
CH2 single channel
|
|
DUAL
|
CH1 and CH2 are displayed ALT or CHOP selectable at any sweep rate.
|
|
ADD
|
CH1+CH2 algebraic addition
|
|
Chopping repetition frequency
|
Approx.250KHz
|
|
Input coupling
|
AC, GND , DC
|
|
Maximum input voltage
|
300V peak (AC: frequency 1KHz or lower) When set probe switch at 1:1, the maximum effective readout is 40Vp p(14Vrms at sine wave); or set probe switch at 10:1, the maximum effective readout is 400Vpp(140Vrms at sine wave)
|
|
Common mode rejection ratio
|
50:1 or better at 50KHz sinusoidal wave.(when sensitivities of CH1 and CH2 are set equally)
|
|
Isolation between channels (at 5Mv/DIV range)
|
＞ 1000:1 at 50 MHz; ＞ 30:1 at 20MHz; ＞ 30:1 at 40MHz
|
|
CH1 signal output
|
At least 20Mv/DIV into a 50 ohm termination, Bandwidth is 50Hz to at least 5MHz.
|
|
CH2 INV BAL
|
Balanced point variation: ≤1DIV(Reference at center graticule)
|
|
|
|
AXA ORIZONTALA
|
|
Sweep time
|
0.2μSec-0.5Sec/DIV,20Steps in 1-2-5sequence
|
|
Sweep time accuracy
|
±3%
|
|
Vernier sweep time control
|
≤1/2.5 of panel-indicated value
|
|
Sweep magnification
|
10 times
|
|
×10MAG sweep time accuracy
|
±5%(20nsec-50nsec are uncalibrated)
|
|
Linearity
|
±3%,×10MAG: ±5%(20ns and 50ns are uncalibrated)
|
|
Position shift caused by×10MAG
|
Within 2 DIV, at CRT screen center
|
|
|
|
DECLANSARE
|
|
Triggering source
|
CH1, CH2, LINE, EXT
|
|
Coupling
|
AC:20Hz to full bandwidth
|
|
Slope
|
+/-
|
|
Sensitivity
|
20Hz-2MHz: 1.0 DIV, TRIG-ALT: 2DIV,EXT:200Mv; 2MHz-20MHz: 1.5DIV; 20MHz or higher: 2.0DIV
TRIG-ALT: 3DIV,EXT:800mv
|
|
TV
|
Sync pulse more than 1 DIV (EXT:1V)
|
|
Triggering modes
|
AUTO; NORM; TV-V; TV-H.
(Both TV-V and TV-H synchronize only when the synchronizing signal is negative)
|
|
Input impedance
|
Approx:1M ohm//approx.25pF
|
|
Max input voltage
|
300V(DC+AC peak), AC: frequency not higher than 1KHz
|
|
|
|
|
X-Y MOD
|
|
|
Sensitivity
|
Same as vertical axis.(X-axis:CH1 input signal,Y-axis:CH2 input signal)
|
|
Frequency bandwidth
|
DC to at least 500KHz
|
|
X-Y phase difference
|
≤3°at DC-50KHz
|
|
|
|
AXA Z
|
|
Sensitivity
|
5Vp-p (positive-going signal decreases intensity)
|
|
Frequency bandwidth
|
DC-2MHz
|
|
Input resistance
|
Approx. 47k ohm
|
|
Maximum input voltage
|
30V (DC+AC peak, AC frequency ≤1KHz)
|
|
|
|
CALIBRAREA VOLTAJULUI
|
|
Waveform
|
positive-going square wave
|
|
Frequency
|
Approx,1KHz
|
|
Output voltage
|
2Vp-p ±2%
|
|
Output impedance
|
Approx,1K ohm
|
|
|
|
CRT
|
|
Type
|
6-inch rectangular type, internal graticule
|
|
Phosphor
|
P31
|
|
Acceleration voltage
|
approx 2KV
|
|
Effective screen size
|
8x10 DIV(1 DIV=10mm(0.39in))
|
|
Graticule
|
Internal
|
|
Trace rotation
|
provided
|
|
|
|
|
|
|
OPTIUNI
|
|
GPIB Communication Module, Serial Interface Communication Module, Pass/Fail Interface Module
|
Validate your login
Conectare
Creează un cont nou