Asiguram reparatii in garantie, in calitate de service provider autorizat pentru Romania. Acordam gratuit asistenta tehnica la achizitie, pentru a demonstra functionalitatea si a arata clientului cum sa lucreze cu statia. La cerere putem preda si cursuri pentru electronistii care vor sa isi dezvolte propria afacere.
• orice statie beneficiaza de garantie 1 an
• 30 zile buy back indiferent de motiv pentru produsele care se livreaza din stoc
• acordam discount pentru cei care aduc statia veche la schimb
• livrarea este gratuita prin Cargus
• plata se efectueaza in avans cu OP
• termenul de livrare pentru produsele care nu se afla in stoc poate depasi in unele cazuri 30 zile
De retinut:
• 30 zile buy back indiferent de motiv pentru produsele care se livreaza din stoc
• acordam discount pentru cei care aduc statia veche la schimb
• livrarea este gratuita prin Cargus
• plata se efectueaza in avans cu OP
• termenul de livrare pentru produsele care nu se afla in stoc poate depasi in unele cazuri 30 zile
DESCRIERE GENRALA:
Osciloscop digital storage DSO5102B
• Banda de frecventa: 200/100/60MHz
• 1GSa/s Real Time sample rate
• Display color de 7.0-inch, WVGA(800x480)
• Poate inregistra pana la 1M
• Mod de declansare: edge/pulse width/line selectable video/slop/overtime etc.
• Dispozitiv de conectare USB , standard
• Masuratori automate multiple
• Are patru functii matematice, inclusiv FFT
• Are conectare PC cu analiza in real-time
• Sisteme de operare: Windows NT, Windows 2000, Windows XP ,VISTA
| Model | DSO5202B | DSO5102B | DSO5062B |
| Banda de frecventa |
200MHz | 100MHz | 60MHz |
| Real-time Sample Rate | 1GSa/s | ||
| Equivalent Sample Rate | 25GSa/s | ||
| Record Length(Sample Points) | Single-channel: Maximum 1M; Dual-channel:Maximum 512K (4K,16K,40K optional) | ||
| SEC/DIV Range | 4nS/div-40S/div (in a 2, 4, 8 sequence) | ||
| Delay Time Accuracy | 500ps | ||
| Vertical | |||
| A/D Converter | 8-bit resolution, each channel sampled simultaneously | ||
| VOLTS/DIV Range | 2mV/div～5V/div at input BNC | ||
| Position Range | ±50V(5V/div),±40V(2V/div～500mV/div),2V(200mV/div～50mV/div)±400mV(20mV/div～2mV/div) | ||
| Bandwidth Limit | 20MHz | ||
| Rise Time at BNC | ≤1.7ns | ≤3.5ns | ≤5.8ns |
| DC Gain Accuracy | ±4% for Sample or Average acquisition mode, 5mV/div to 2mV/div ±3% for Sample or Average acquisition mode, 5V/div to 10mV/div |
||
| Trigger | |||
| Trigger Sensitivity (Edge Trigger Type) |
DC: CH1/CH2(Typical) 1div from DC to 10MHz;1.5div from 10MHz to Full EXT（Typical） 200mV from DC to 40MHz EXT/5（Typical） 1V from DC to 40MHz AC: Attenuates signals below 10Hz HF Reject: Attenuates signals above 80kHz LF Reject: Attenuates signals below 150kHz Noise Reject: Reduces trigger sensitivity |
||
| Trigger Level Range | CH1,CH2: ±8 divisions from center of screen EXT: ±1.2V EXT/5: ±6V |
||
| Trigger Level Accuracy, typical (Accuracy is for signals having rise and fall times ≥20ns) |
CH1,CH2: ±(0.3div×V/div) (within ±4 divisions from center of screen) EXT: ±(6% of setting + 40mV) EXT/5: ±(6% of setting + 200mV) |
||
| Holdoff Range | 100ns-10s | ||
| Trigger Type | |||
| Edge | Trigger on the rising or falling edge | ||
| Pulse Width | Trigger (when >,<,=,≠) on positive or negative pulses Pulse Width Range: 20ns-10s |
||
| Video | Trigger on an NTSC, PAL, or SECAM standard video signal Line Range: 1-525 (NTSC), 1-625 (PAL/SECAM) |
||
| Slope | Trigger (when >,<,=,≠) on a positive or negative slope Set Time: 20ns–10s |
||
| Overtime | from the rising or falling edge Set Time: 20-10s |
||
| Alternate | Internal trigger on edge, pulse width, video or slope | ||
| Measurement | |||
| Cursors | Manual: The difference between voltage cursors △V; the difference between time cursors △T; 1/△T calculated by Hz. Tracing: The voltage and time at a waveform point |
||
| Automatic | Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width | ||
| Display | |||
| Type | Right angle 7"TFT 16-digit color LCD | ||
| Resolution | 800*480 dots | ||
| Contrast | 16 gears, with the progress bar to show adjustment | ||
| Interface | USB host and USB slave | ||
| Power Supply | |||
| Voltage | 100-120VACRMS(±10%)，45Hz to 440Hz，CATⅡ 120-240VACRMS(±10%)，45Hz to 66Hz，CATⅡ |
||
| Power | <30W | ||
| Fuse | 2A, T rating, 250V | ||
| Mechanical | |||
| Size | Length: 313mm Width: 108mm Height: 142mm | ||
| Weight | 2.08KG (exclusive of packing and accessories) | ||